setrvery.blogg.se - Shark duo clean vacuum remove brush

Detach the brush roll carefully so you don’t damage the belt holding it in place. If the brush roll will not completely detach, try rotating the brush roll counterclockwise until it comes free. Shark vacuums have a brush roll that slips out of the compartment with ease, while the other end must be pulled out of its holding belt. If your Shark has not been performing the way it usually does, giving it a good clean will really bring it back to life.Brush rolls can sometimes be difficult to remove from vacuum belts because they are located together with other vacuum components. In all honesty, I would say the whole drying of the filters takes longer than the actual cleaning process. People make the mistake of thinking that just because Shark says their vacuums never lose suction that they do not have to do anything to make that so.Ĭleaning a vacuum is not a pleasant experience, but it is not hard at all. Your Shark vacuum gives you so much and it asks for so little in return. Step 5: Once they are fully dried you can put them back in the vacuum cleaner and you are ready to go! The HEPA filters can wear out over time (a very long time) so make sure you get replacement ones if the vacuum still smells odd even after a good cleaning.Even if they are just a little bit damp, do not put them back in the vacuum cleaner. You will find that the plastic based one dry very quickly, but the others can take a very long time, especially the HEPA filters. Step 4: Now this is very, very important.Keep rinsing until the water coming out of them is clear. You can use some mild washing detergent if you want, but I would advise using a tiny amount. Be gentle and just give them a little squeeze or rub to get all the dust out. The HEPA filters and the other filters of the vacuum should be cleaned the same way. Step 3: Using mildly warm water give the filters a rinse.This will make your cleaning much easier and less disgusting. Give them a little tap over the garbage can to shake off as much dust as you can. Step 2: I am not going to lie, these things are gross! Before you start the cleaning process.What I did when I first got the vacuum I have now is take a picture on my phone. Now, this is nice and easy to do, but make sure you make a mental note of where each one goes this makes putting them back much easier. If you do, make sure you are very gentle.

One extra thing I want to say is that when it comes to the regular filters (not the HEPA ones) some Shark vacuum models have felt and others use rubber filters.įelt filters are much more delicate and Shark does not actually recommend that you wash them so do so at your own risk. These instructions will work for HEPA filters and also the regular standard kind. If your vacuum smells a bit funky, the filters need cleaning. These are what keep all the nasty dust and allergens inside the vacuum. When it comes to filters the main ones that make a Shark vacuum cleaner so good are the HEPA filters. It takes a couple of minutes if that and then you just need to leave it to fully dry.

Step 2: I am a bit excessive so I like to get a baby wipe and clean as much of the inside of the canister as I can.

Some people do this and leave it at that and never have an issue.

Step 1: Remove the canister from your Shark vacuum and empty all of the garbage.

Cleaning The CanisterĬleaning the canister is not the grossest part of this job like you may think it is! This is actually very easy to do. The short instructional video above from Shark will show you how to take the bottom off a Shark vacuum and guide you through the process. The soft roller brush can also be ejected and cleaned. Once the panel is removed, the DuoClean brush roll can be removed.Īny hair or dirt can be removed, and there is even a hair removal tool that is included and is found under the panel. This involves removing the top panel, or ‘garage’, which is located on the vacuum head. The Shark Duoclean range, including the Powered Lift-Away, Rocket Ultra-Light, IONFlex Cordless, Apex, and the Lift-Away Speed, all feature an easy-to-clean brush roll system.

Step 3: Once I have removed all the debris that I can see I like to use a small brush and give the rotating brush a gentle scrub to remove the last little bits of debris that I may have missed.

Sometimes it is easier to get a pair of scissors and cut out the pet hair than untangle it. Old bits of food, Lego, pet hair and other such things.

Step 2: Look for anything that is stuck in the rotating brush.You may want to put it on a garbage bag or do it outside if you are worried about the mess. Step 1: Make sure your vacuum is off (look I know it is common sense, but I have to say it) and turn it over.If you have pets then more than likely it will be pet hair. It is crazy the things that can get stuck in here.